A Studio Display Was Cutting This User's Download Speed by 75%

My Monitor Was Cutting My Download Speed by 75%

A Studio Display Was Cutting This User's Download Speed by 75%

A blogger with a 2.5 Gbps symmetrical line noticed downloads stuck at 600 Mbps while uploads ran at full speed. Plugging the adapter straight into the Mac restored 2.3 Gbps, so the 2026 Studio Display XDR's hub was the culprit. Digging into USB burst sizes and Realtek drivers, he found the RTL8156B adapter's tiny 4-packet bursts couldn't keep up through the display, and a 5 Gbps RTL8157 adapter fixed it.

I don't think I've ever run a speed test through it. 600 Mbps was more than fast enough for me to never realise I wasn't getting three quarters of the speed I was paying for.
  1. frizkie

    I had the same problem recently when trying to figure out high bandwidth game streaming from my desktop to my Steam deck in the living room. The beta streaming tech is “pyrowave” and it is super low latency and looks INCREDIBLE compared to traditional codecs, but as a trade off it is extremely sensitive to packet loss, and uses an appropriately large amount of bandwidth (7-800mbit at 4k120). Wired network isn’t _strictly_ a requirement but it might as well be, and the steam deck doesn’t have a physical port - but the steam deck dock does.

    Anyway, the exact same situation arises, where some network condition or physical configuration (there’s a lot of hardware in between these two devices, including MoCA adapters) meant that the network adapter buffer fills up and starts dropping packets. The buffer size is configurable through some terminal command and maxing that out makes the issue disappear immediately.

  2. senko

    This reminds me of a (completely different, but felt equally) bizzare problem with ghostty (the terminal emulator) on Linux and Steam, specifically Baldur's Gate 3.

    At the start of the game after an update, BG3 compiles the (Vulkan) shaders. To avoid hammering the computer, it checks the load, including I/O pressure, and then throttles itself. It turns out that Ghostty uses io_uring, and even if it's not doing anything this somehow counts as pressure. This was made worse by the fact that I usually have a dozen or so Ghostty windows.

    End result, BG3 compiles shaders using 1 core, throttled, instead of all available 20 cores. Instead of a minute or so, it'd take several hours.

    (For closure: I configured ghostty to use epoll instead. Probably not optimal but works around the problem.)

  3. manarth

    Better description: "My USB network switch was cutting my download speed".

    The fact that it's a monitor is a little bit irrelevant.

  4. throw0101d

    Meta:

    > Somehow I am one of those few very lucky people to have the opportunity of owning a 2.5 gig symmetrical line for my internet.

    I'm not going to complain against more bandwidth (as a GenXer I stared my online journey at (IIRC) 9600bps (maybe lower): much celebration with V.32/V.90), but I'm curious to know how many residential use-cases can take advantage of that much bandwidth. Linux ISOs?

    How many services allow that much speed on a single stream / (TCP) session? Maybe you could have five at 500 Mbps?

    Certainly downloading security updates or games may be quicker, but I would think that above 500Mbps (and certainly 1 Gbps) there would be major diminishing returns. Is anyone regularly getting close to that utilization in their daily work / hobbies (and not just a momentary spike on patch Tuesday)?

  5. fancyfredbot

    Since lots of comments misunderstood the article, the extra latency from going through the monitor meant his laptop couldn't acknowledge the packets quickly enough. That led a buffer on the ethernet adapter to fill and that led it to drop packets.

    A different adapter which required less frequent acknowledgement fixed the problem for him.

    It is quite a nice post which gets to the bottom of incredibly opaque behaviour of USB hubs.

  6. gh123man

    I have nothing useful to add other than I feel so validated reading this. Ive been struggling with this issue on and off for over a year. With the release of Astra, it was able to finally unstick me to the point of enabling flow control which has been good enough.

    I experienced this problem with a macbook and a thunderbolt dock. I had tried multiple different brands of docks and ethernet adapters, and various macbooks. One interesting thing I discovered is if I plugged a non-thunderbolt cable between the dock and the laptop, I would achieve full speed with no packet loss, so interestingly the issue doesn't occur over pure USB but only over thunderbolt.

    This has got to be a bug on Apple's side right? Would be nice if they fixed it.

  7. zodwick

    >It’s run by this one guy

    This was super surprising, have always thought ISPs are a super hard businesses. But good for you mate, good ISPs are lifesavers.

    I have had the opposite experience with my ISP guys. One of the VMs I got as part of work only had IPv6 and to my shock my internet didn't have one. When I contacted my ISP they legit told "You can either have IPv4 or IPv6, but not both". Unfortunately I was on a 12 month plan and couldn't easily cancel so ended up working around using tailscale.

  8. srcreigh

    Nice post. Unsatisfying conclusion - did you ever figure out why the original adapter was throttled when plugged into the monitor, and not when plugged into the computer?

More from this day

2026-11-21